Tire Size Comparison Calculator

Your speedometer and odometer are calibrated to the rolling circumference of the factory tire (83.82 in per revolution). Moving to 235/45R18 (82.71 in circumference) changes revolutions per mile from 755.9 to 766.1 — a +10.2 rev/mi shift. At 60 mph indicated on your cluster, true road speed becomes approximately 59.2 mph (-1.33% error). That -1.33% variance sits within the ±2–3% band most OEMs target for speedometer accuracy, so daily driving and typical enforcement margins are usually unaffected. Odometer distance will also skew proportionally: over 10,000 miles, a 1.3% error accumulates to roughly 133 miles of discrepancy versus actual distance traveled.

The dimensional delta is moderate — -0.35 in in diameter and -0.39 in in section width — so many vehicles with healthy factory clearance margins can accept this swap without modification. Still verify at full steering lock and under maximum suspension compression; even modest growth can contact the pinch weld or liner on tightly packaged platforms (especially performance sedans and lowered trucks). Wheel offset and backspacing matter as much as tire size. Key contact points to inspect: front inner fender liner at full lock, rear quarter panel lip under load, pinch weld on the unibody rail, and the leading edge of the rear bumper cutout on short-bed trucks. A wider tire (-0.39 in, -4.08%) increases scrub radius slightly, which can add steering effort and transmit more road noise through the rack. If your vehicle uses adaptive cruise, lane-keep, or automatic emergency braking, confirm that radar and camera calibrations are unaffected — some systems are sensitive to ride-height changes.

The -0.18 in change in static ride height is small enough that most factory-height vehicles can absorb it without a lift kit. You still gain the full diameter benefit for obstacle clearance and break-over angle — just confirm that the larger tire does not contact the fender, liner, or control arms at full suspension travel before relying on the extra clearance off-road. Static ground clearance changes by -0.18 in because overall diameter shifts -0.35 in (-1.33%). That half-diameter rule applies at each axle: a 0.35" diameter change adds roughly 0.18" of clearance under the differential and rocker panels. Approach and departure angles improve proportionally, which matters for off-road and steep driveway transitions. For street-only vehicles, the priority is avoiding contact at full compression rather than maximizing lift height.

Revs per mile increase by +10 (+1.35%), meaning the engine turns 10 more RPM at 60 mph (756 → 766 RPM). Higher cruising RPM raises internal friction losses and can trim highway fuel economy by 1–3% in real-world driving, though the effect varies with gearing, aerodynamics, and how much the wider contact patch increases rolling resistance. City driving impact is usually smaller because speeds are lower. Rolling circumference changed -1.11 in (-1.33%), which is the primary driver of cruising RPM. Sidewall height changed -0.18 in — a shorter sidewall reduces flex and heat buildup at speed but transmits more road harshness. For the most accurate estimate, track a full tank before and after the swap on your regular commute.

Both 245/45R18 and 235/45R18 mount on 18" wheels, so your existing rims may work if the internal barrel width and offset support the 235 mm section width. As a rule of thumb, each 10 mm of tire width typically needs ~5 mm of additional wheel width. Verify that the new tire's load index and speed rating meet or exceed your vehicle's requirements, and confirm that the wheel's backspacing positions the bead correctly relative to the hub face — incorrect offset is a leading cause of rubbing even when the tire diameter fits.

Overall diameter increases -0.35 in (-1.33%), from 26.68" to 26.33". Static ground clearance at the lowest point (typically the differential pumpkin or exhaust crossmember) rises by approximately -0.18 in — half the diameter delta. Break-over angle improves because the contact patches move farther from the center of the vehicle, reducing the likelihood of high-centering on obstacles. Note that a smaller diameter reduces clearance and increases break-over vulnerability — confirm this tradeoff aligns with your use case.

Modern ABS and ESC systems compare wheel-speed sensor inputs across all four corners to detect slip. A +10.2 rev/mi change alters the expected wheel-speed ratio at any given road speed by +1.35%. At this magnitude, most factory ABS/ESC modules tolerate the variance without fault codes, though a brief relearn drive cycle (10–15 minutes of mixed driving) helps the system establish new baselines. Traction control and hill-descent systems use the same wheel-speed data, so the same tolerance applies. If your vehicle has tire-pressure monitoring, confirm the new size is within the TPMS relearn parameters for your module.

Sidewall height moves from 4.34" to 4.16" (-0.18", -4.08%). Sidewall height is similar, so ride/handling character should remain largely unchanged. Section width changes -0.39 in (-4.08%), which narrows the footprint, potentially improving snow penetration and reducing rolling resistance at the expense of ultimate dry grip. Match tire compound and tread pattern to your climate and driving style for best results.